Carbide Hole Saw Cutter

Carbide Hole Saw Cutter

Carbide Hole Saw Cutter

Blue Boar MEGA Tungsten Carbide Tipped (TCT) hole saws. All models cut wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials

• Cut 40x more holes per charge with cordless drills
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cut holes in 1/10 the time over bi-metal hole saws
• Cut 6" holes in 1" thick plywood with 18v cordless drills
• Tough Tungsten Carbide teeth extend past inside and outside walls for reduced friction and much faster cutting
• Large side gullet slots for fast chip removal and fast plug removal
• Ultra Deep 2-1/4" cutting depth
• Use with standard hole saw arbors
• All hole cutters work with standard length 3-3/4" pilot drill bits and the new tungsten carbide tipped pilot bits for wood and engineered wood (MDF, particle board, etc.)

Products

Blue Boar Dual Arbor and Hole saw starter case kit with 3 pilot bits

Dual Arbor and Hole saw starter case kit with 3 pilot bits includes:
• Heavy duty molded case
• Carbide tipped masonry pilot drill bit
• Porcelain pilot drill bit
• 5/8”-18 thread   2-pin hole saw arbor adapter with HSS pilot bit
• Use 5/8”-18 2-pin mount for hole saws 1-1/4” and larger and ½”-20 adapter for smaller hole saw sizes

HP1596

$18.95

Blue Boar 7/16-inch shank Dual Arbor Mandrel Kit

One Arbor Kit provides two Hole Saw arbor mandrels that store in the space of one ordinary arbor
• Use 5/8”-18 2-pin mount for hole saws 1-1/4” and larger ½”-20 adapter for smaller hole saw sizes
• 7/16-inch hex shank for greater gripping capability in the chuck. Use with standard arbor extension
• Comes with standard ¼” high speed steel pilot drill bit
• For all hole saws from 5/8 inch to 7 inches in diameter

HP1597

$12.99

Blue Boar 1/4" x 3-7/8" Carbide Pilot bit

Blue Boar 1/4" x 3-7/8" TCT Pilot Bit in plastic tube
• Good for use on hard and engineered woods, MDF, particle board, OSB, plywood, etc.
• The tapered shaft provides easy plug removal. Bores faster and stays sharp longer than carbon steel spade bit and high speed steel twist pilot bits

HP1598

$6.99

Blue Boar 5/8" (16mm) carbide 2-1/4" deep hole saw

Technical Details
• 5/8" (16mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 1 TCT carbide tooth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1609

$8.45

Blue Boar 3/4" (19mm) carbide 2-1/4" deep hole saw

• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit

HP1610

$8.45

Blue Boar 7/8" (22mm) carbide 2-1/4" deep hole saw

Technical Details
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• 7/8" (22mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 1 TCT carbide tooth
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1611

$9.20

Blue Boar 1" (25mm) carbide 2-1/4" deep hole saw

Technical Details
• 1" (25mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1612

$11.00

Blue Boar 1-1/8" (29mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-1/8" (29mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1613

$14.05

Blue Boar 1-1/4" (32mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-1/4" (32mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1614

$15.40

Blue Boar 1-3/8" (35mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-3/8" (35mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1615

$14.75

Blue Boar 1-1/2" (38mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-1/2" (38mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1616

$15.00

Blue Boar 1-5/8" (41mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-5/8" (41mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1617

$15.25

Blue Boar 1-3/4" (45mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-3/4" (44mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1618

$15.50

Blue Boar 1-7/8" (48mm) carbide 2-1/4" deep hole saw

Technical Details
• 1-7/8" (48mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 2 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1619

$15.75

Blue Boar 2" (51mm) carbide 2-1/4" deep hole saw

Technical Details
• 2" (51mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

HP1620

$16.00

Blue Boar 2-1/16" (52mm) carbide 2-1/4" deep hole saw

Technical Details
• 2-1/16" (52mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1621

$16.50

Blue Boar 2-1/8" (54mm)carbide 2-1/4" deep hole saw

Technical Details
• 2-1/8" (54mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1622

$16.80

Blue Boar 2-1/4" (57mm) carbide 2-1/4" deep hole saw

Technical Details
• 2-1/4" (57mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide tooth
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1623

$17.30

Blue Boar 2-1/2" (64mm)carbide 2-1/4" deep hole saw

Technical Details
• 2-1/2" (57mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1624

$17.50

Blue Boar 2-9/16" (65mm) carbide 2-1/4" deep hole saw

Technical Details
• 2-9/16" (65mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1625

$18.00

Blue Boar 2-5/8" (67mm) carbide 2-1/4" deep hole saw

Technical Details
• 2-5/8" (67mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1626

$18.00

Blue Boar 2-3/4" (70mm) carbide 2-1/4" deep hole saw

Technical Details
• 2-3/4" (70mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1627

$20.00

Blue Boar 3" (76mm) carbide 2-1/4" deep hole saw

Technical Details
• 3" (76mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1628

$22.00

Blue Boar 3-1/8" (80mm) carbide 2-1/4" deep hole saw

Technical Details
• 3-1/8" (80mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1629

$23.50

Blue Boar 3-3/8" (86mm) carbide 2-1/4" deep hole saw

Technical Details
• 3-3/8" (86mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1630

$24.00

Blue Boar 3-1/2" (89mm) carbide 2-1/4" deep hole saw

Technical Details
• 3-1/2" (89mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1631

$24.50

Blue Boar 3-5/8" (92mm) carbide 2-1/4" deep hole saw

Technical Details
• 3-5/8" (92mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1632

$23.00

Blue Boar 4" (102mm) carbide 2-1/4" deep hole saw

Technical Details
• 4" (102mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1633

$28.50

Blue Boar 4-1/8" (105mm) carbide 2-1/4" deep hole saw

Technical Details
• 4-1/8" (105mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1634

$29.00

Blue Boar 4-1/4" (108mm) carbide 2-1/4" deep hole saw

Technical Details
• 4-1/4" (108mm) MEGA Tungsten Carbide 2-1/4" deep hole saw
• 3 TCT carbide teeth or more
• Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw
• Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials
• Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit
• Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off
• USE on cordless drill MEDIUM to HIGH SETTING for best results

***Arbor and pilot bit NOT INCLUDED***

HP1635

$30.00