Blue Boar MEGA Tungsten Carbide Tipped (TCT) hole saws. All models cut wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials. Does NOT cut Metal. • Cut 40x more holes per charge with cordless drills • Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw • Cut holes in 1/10 the time over bi-metal hole saws • Cut 6" holes in 1" thick plywood with 18v cordless drills • Tough Tungsten Carbide teeth extend past inside and outside walls for reduced friction and much faster cutting • Large side gullet slots for fast chip removal and fast plug removal • Ultra Deep 2-1/4" cutting depth • Use with standard hole saw arbors • All hole cutters work with standard length 3-3/4" pilot drill bits and the new tungsten carbide tipped pilot bits for wood and engineered wood (MDF, particle board, etc.)
Dual Arbor and Hole saw starter case kit with 3 pilot bits includes: • Heavy duty molded case • Carbide tipped masonry pilot drill bit • Porcelain pilot drill bit • 5/8”-18 thread 2-pin hole saw arbor adapter with HSS pilot bit • Use 5/8”-18 2-pin mount for hole saws 1-1/4” and larger and ½”-20 adapter for smaller hole saw sizes
One Arbor Kit provides two Hole Saw arbor mandrels that store in the space of one ordinary arbor • Use 5/8”-18 2-pin mount for hole saws 1-1/4” and larger ½”-20 adapter for smaller hole saw sizes • 7/16-inch hex shank for greater gripping capability in the chuck. Use with standard arbor extension • Comes with standard ¼” high speed steel pilot drill bit • For all hole saws from 5/8 inch to 7 inches in diameter
Blue Boar 1/4" x 3-7/8" TCT Pilot Bit in plastic tube • Good for use on hard and engineered woods, MDF, particle board, OSB, plywood, etc. • The tapered shaft provides easy plug removal. Bores faster and stays sharp longer than carbon steel spade bit and high speed steel twist pilot bits
Technical Details • 5/8" (16mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 1 TCT carbide tooth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3/4" (19mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 1 TCT carbide tooth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 7/8" (22mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 1 TCT carbide tooth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1" (25mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-1/8" (29mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-1/4" (32mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 1/2"-20 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-3/8" (35mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
b>Technical Details • 1-1/2" (38mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-5/8" (41mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-3/4" (44mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 1-7/8" (48mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 2 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2" (51mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-1/16" (52mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • Cut 3 times as large a hole using cordless hand drills than with a bi-metal hole saw • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-1/8" (54mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-1/4" (57mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide tooth • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-1/2" (57mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-9/16" (65mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-5/8" (67mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 2-3/4" (70mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3" (76mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3-1/8" (80mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3-3/8" (86mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3-1/2" (89mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 3-5/8" (92mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 4" (102mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
b>Technical Details • 4-1/8" (105mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results
Technical Details • 4-1/4" (108mm) MEGA Tungsten Carbide 2-1/4" deep hole saw • 3 TCT carbide teeth or more • Cuts wood, sheetrock, fiber cement board, plaster, fiberglass, OSB, chipboard, MDF, and other tough materials • Use any 5/8"-18 thread hole saw arbor and any standard 3-3/4" or longer pilot bit • Do NOT use with 1/2" stud drills such as Milwaukee Hole Hawg which will cause the teeth to rip off • USE on cordless drill MEDIUM to HIGH SETTING for best results